HAIR & BEARD OIL: FOR HAIR

As our oil is made up of only 100% pure and natural oil, the way in which you use it depends on your hair type, wash schedule and personal preference!

Roots: Rub 2 pumps of oil with your fingertips and rake/comb through into roots and scalp (do not rub/excessively massage, to avoid manual hair pulling). Use this treatment twice a week and leave it in for a maximum of 1-2 days.

All over hair: Using 2 pumps of oil, rake/comb through your roots using your fingertips. Depending on the length of your hair, apply 3-4 pumps onto the palms of your hand and gently run this through the lengths of your hair. Feel free to use more, e.g. if you have longer/thicker hair. Do this twice a week and leave it in for a maximum of 1-2 days.

Ends: Pour 1 pump of oil into the palms of your hand and rub them together. Push all hair to one side or gather in a bunch and gently press the oil into the ends of your hair. This can be applied daily and left in until you next wash (3-4 days).

HAIR & BEARD SCRUB

Step 1 - Before washing hair when dry, part the hair and distribute scrub directly onto the scalp across the crown and the back of the head.

Pro Tip: We recommend 6-8 'lines' in total to fully cover the scalp.

Step 2 - Massage in with fingers and leave to sit for 5 minutes, allowing the chemical exfoliants to do their magic!

Step 3 - Step into the shower and run warm water over your head to melt the beads and reveal a fresh, cleansed and nourished scalp ready to receive all the goodness of your shampoo!We advise using this 1x per week as a clarifying detox.

Pro Tip: The same method applies for the beard, however no need to draw partings, just squeeze the scrub to the tips of your fingers and massage into the skin beneath your beard.

SHAMPOO

As our shampoo is made up of only 100% naturally derived ingredients, the way in which you’d use it depends on your hair type, wash schedule and personal preference. 

Hair: Wet your hair and go in with a few pumps of the shampoo. Make sure to rub it in your palms to activate the natural foaming action. You can apply to your roots, scalp, lengths and ends. Make sure to give it a good squeeze to get it properly cleaned and then finally rinse with water and make sure you lift at the roots to ensure that every part of your scalp has been throughly cleaned. 

Beard: Wet your beard and go in with 2-3 pumps of the shampoo. Make sure you rub it in your palms to activate the natural foaming action. You can then gently apply it all over your beard and deep into the roots, length and ends. Give it a good squeeze to get it properly cleaned and then finally rinse with water. 

CONDITIONER

After rinsing your hair of the shampoo, go in with a few pumps of the conditioner. The amount of pumps will depend on your hair length but we recommend using our conditioner from root to tip so your hair is fully coated. For the best results, use the luxury hair brush to evenly spread the product and then rinse out as usual.

Lengths: The most common way of applying hair conditioner has always been to the lengths. This is when you evenly spread it to the ends of your hair and leave it for 1 minute before washing it off! It works great for scalps that gets oily easily, as you would essentially avoid that area. 

Leave in treatment: Another way you can use the conditioner is with leaving it in your hair! The natural properties will bring in the shine and leave your hair glossy and moisturised. 

Hair mask: Finally, treat your hair and scalp to a hair mask using our conditioner - the consistency is thick and fluffy which makes it perfect to apply it all over your hair and then tie it up in a bun and allow the conditioner to work its magic. You can then wash it off after 15-20 mins and watch your hair turn silky smooth!

HAIR & BEARD OIL: FOR BEARD

Step 1 - Get 1-3 pumps depending on the length of your beard. 

Step 2 - Start off by rubbing your hands together to ensure your fingertips and palms are evenly coated. 

Step 3 - Push the beard upwards so that the oil touches the skin as well as the lengths of the beard hair. 

Step 4 - Press and massage as you go 

Step 5 - Don’t forget your moustache! 

Step 6 - Finish off with shaping and styling your beard.

BEARD SCRUB

Step 1 - Squeeze the scrub to the tips of your fingers. 

Step 2 - Gently massage into the skin beneath your beard. 

Step 3 - Wash off after 5 minutes. 

Step 4 - Pat dry your beard. 

Pro Tip: Use 1-2 drops of ByErim oil to the beard post scrub for the shine and styling of beard.

MESSAGE OUR 24/7 HAIR CONCIERGE WITH ANY QUESTIONS

How to Use

HAIR & BEARD OIL: FOR HAIR

HAIR & BEARD OIL: FOR HAIR

As our oil is made up of only 100% pure and natural oil, the way in which you use it depends on your hair type, wash schedule and personal preference!

Roots: Rub 2 pumps of oil with your fingertips and rake/comb through into roots and scalp (do not rub/excessively massage, to avoid manual hair pulling). Use this treatment twice a week and leave it in for a maximum of 1-2 days.

All over hair: Using 2 pumps of oil, rake/comb through your roots using your fingertips. Depending on the length of your hair, apply 3-4 pumps onto the palms of your hand and gently run this through the lengths of your hair. Feel free to use more, e.g. if you have longer/thicker hair. Do this twice a week and leave it in for a maximum of 1-2 days.

Ends: Pour 1 pump of oil into the palms of your hand and rub them together. Push all hair to one side or gather in a bunch and gently press the oil into the ends of your hair. This can be applied daily and left in until you next wash (3-4 days).

<button>Here<button>

Delivery details

Add additional information about delivery policy.

Refund details

Add additional information about refund policy.

Topic heading

Descriptive topic content body text