HAIR & BEARD SCRUB
Before washing hair when dry, part the hair and distribute scrub directly onto scalp across the crown and the back of the head.
We recommend 6-8 'lines' in total to fully cover the scalp.
Massage in with fingers and leave to sit for 5 minutes, allowing the chemical exfoliants to do their magic!
Step into the shower and run warm water over your head to melt the beads and reveal a fresh, cleansed and nourished scalp ready to receive all the goodness of your shampoo!
We advise using this 1x per week as a clarifying detox.
The same method applies for the beard, however no need to draw partings, just squeeze the scrub to the tips of your fingers and massage into the skin beneath your beard.
HAIR & BEARD OIL: FOR HAIR
As our oil is made up of only 100% pure and natural oil, the way in which you use it depends on your hair type, wash schedule and personal preference!
Roots: Rub 2 pumps of oil with your fingertips and rake/comb through into roots and scalp (do not rub/excessively massage, to avoid manual hair pulling). Use this treatment twice a week and leave it in for a maximum of 1-2 days.
All over hair: Using 2 pumps of oil, rake/comb through your roots using your fingertips. Depending on the length of your hair, apply 3-4 pumps onto the palms of your hand and gently run this through the lengths of your hair. Feel free to use more, e.g. if you have longer/thicker hair. Do this twice a week and leave it in for a maximum of 1-2 days.
Ends: Pour 1 pump of oil into the palms of your hand and rub them together. Push all hair to one side or gather in a bunch and gently press the oil into the ends of your hair. This can be applied daily and left in until you next wash (3-4 days).
As our shampoo is made up of only 100% naturally derived ingredients, the way in which you’d use it depends on your hair type, wash schedule and personal preference.
Hair: Wet your hair and go in with a few pumps of the shampoo. Make sure to rub it in your palms to activate the natural foaming action. You can apply to your roots, scalp, lengths and ends. Make sure to give it a good squeeze to get it properly cleaned and then finally rinse with water and make sure you lift at the roots to ensure that every part of your scalp has been throughly cleaned.
Beard: Wet your beard and go in with 2-3 pumps of the shampoo. Make sure you rub it in your palms to activate the natural foaming action. You can then gently apply it all over your beard and deep into the roots, length and ends. Give it a good squeeze to get it properly cleaned and then finally rinse with water.
After rinsing your hair of the shampoo, go in with a few pumps of the conditioner. The amount of pumps will depend on your hair length but we recommend using our conditioner from root to tip so your hair is fully coated. For the best results, use the luxury hair brush to evenly spread the product and then rinse out as usual.
Lengths: The most common way of applying hair conditioner has always been to the lengths. This is when you evenly spread it to the ends of your hair and leave it for 1 minute before washing it off! It works great for scalps that gets oily easily, as you would essentially avoid that area.
Leave in treatment: Another way you can use the conditioner is with leaving it in your hair! The natural properties will bring in the shine and leave your hair glossy and moisturised.
Hair mask: Finally, treat your hair and scalp to a hair mask using our conditioner - the consistency is thick and fluffy which makes it perfect to apply it all over your hair and then tie it up in a bun and allow the conditioner to work its magic. You can then wash it off after 15-20 mins and watch your hair turn silky smooth!
HAIR & BEARD OIL: FOR BEARD
Use 1 pump in the morning or evening. Gently apply the oil from the roots to the ends of your beard. This can be left in for up to 1 day and applied 3-4 times a week.